Cirronet HN 210X Guida Utente Pagina 39
- Pagina / 52
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
HN-2010
Set Maximum Number of Remotes (base only)
This parameter limits the number of remotes that can register with a given base. The
default is 62 remotes which is the maximum number of remotes that can be registered
with a base at one time. This command is useful when used in conjunction with
global roaming for load balancing when base stations are collocated. It is also useful
to assure a minimum remote throughput.
Set Packet Attempts Limit
If ARQ Mode is set to 0, sets the number of times the radio will attempt to send an
unsuccessful transmission before discarding it. If ARQ Mode is set to 1, it is the
number of times every transmission will be sent, regardless of success or failure of a
given attempt. When this parameter is set to FFH, RF flow control mode is entered
for transmissions from the radio (See Section 2.3.4). This mode can be entered for
one or both radios in a point-to-point system. Using this mode in a point-to-multipoint
system will stop transmissions to all radios when any one radio has a full buffer.
Set Data Transmit Delay
When used in conjunction with the minimum data length parameter, this sets the
amount of time from the receipt of a first byte of data from the host until the radio
will transmit in transparent mode. Default is 00H which causes transmission to occur
without any delay. When a host is sending a group of data that needs to be sent
together, setting this parameter will provide time for the group of data to be sent by
the host before the radio transmits. If the length of data to be sent together is longer
than the time slot can send, the data will not be sent together but will be broken up
over multiple hops. The length of time the radio will wait is equal to the specified
value times the hop duration.
Set Slot Assignment Mode (base station only)
Sets whether the base station will assign remote transmit slots dynamically, based on
the number of remotes currently registered or whether the base station will assign
remote transmit slots statically, based on the maximum number of remotes parameter.
If static slot assignment is selected, make sure maximum number of remotes is
correctly set. Otherwise remote transmit performance will suffer as transmit time will
be reserved for remotes that may not exist. The dynamic assignment mode will
generally be preferred; however, the static assignment mode will result in a static
maximum data length parameter.
© 2000- 2004 Cirronet™ Inc 33 M-2410-0011 Rev B
- HN-2010 1
- User’s Guide 1
- Declaration of Conformity 3
- Table of Contents 4
- Overview 7
- Design Features 8
- Glossary of Terms 9
- About HopNet Products 10
- HN-2010 Repeater 11
- RF Antenna Connectors 12
- Conxall Power Connector 12
- DB-9 Connector 13
- Three-Way Switch 13
- LED Status 14
- Antenna Connectors 15
- Configuring the Repeater 16
- Technical Specifications 17
- Mechanical 18
- Environmental 18
- Configuring the Network 19
- Starting the program 22
- Function Keys 25
- WinCom Tools 26
- Script Commands 28
- Demonstration Procedure 31
- Modem Commands 32
- Serial Commands 32
- Set Data Rate Divisor 33
- Set Protocol Mode 33
- Network Commands 34
- Enable Global Network Mode 35
- Set Hopping Pattern 35
- Set Transmit Power 35
- Set Range Optimization 36
- Protocol Commands 37
- Set Hop Duration 38
- Set Minimum Data Length 38
- Set Packet Attempts Limit 39
- Set Data Transmit Delay 39
- Set ARQ Mode 40
- Status Commands 41
- Set Duty Cycle 42
- Memory Commands 43
- Modem Command Summary 44
- Guidelines for Installation 45
- Typical HopNet Applications 46
- Troubleshooting 47
- Common System Problems 48
- Introduction 49
- Customer Support 51
- Warranty 52
Prodotti e manuali riguardandi Networking Cirronet HN 210X
Networking Cirronet CR-SEH Manuale Utente
(2 pagine)
(2 pagine)
Networking Cirronet CR-SEB Manuale Utente
(2 pagine)
(2 pagine)
Networking Cirronet CR-SEB/X Manuale Utente
(34 pagine)
(34 pagine)
Networking Cirronet SEM2410 Guida Utente
(37 pagine)
(37 pagine)
Networking Cirronet CR-SEHX Manuale Utente
(34 pagine)
(34 pagine)
Networking Cirronet HN214D Guida Utente
(64 pagine)
(64 pagine)
Electrolux EDC66130W manuals
Owner’s manuals and user’s guides for Coffee making accessories Electrolux EDC66130W.
We providing 3 pdf manuals Electrolux EDC66130W for download free by document types: User Manual
Commenti su questo manuale